Verex MONITOR AFx Uživatelská příručka stáhnout pdf (Strana 191)

500-9041 v4.1

Welcome Report Control Admin

Sys Config

Tech-Ref

185

scheduled 'closing' time, area keypads will beep

to remind staff to either arm the area and exit, or

delay the closing time (worklate). If neither of

these actions occur, an alarm can be

transmitted, and/or the area can be armed

automatically (as per settings to follow).

Tip:

Pause the mouse cursor over a schedule in the

list to see the settings for that schedule.

To define a schedule, refer to "Schedules for User

Access and Area Automation".

A programmable output can be set to signal when the

area closing time is approaching. For details, refer to

"Programmable Outputs".

- Out of Schedule:

The length of time before the

area will automatically 're-close' after an

'emergency off' is performed

(i.e., being disarmed

outside

of the schedule).

This limits the time that an "Emergency Off" can

remain in effect.

- In Schedule:

The length of time before the area

will automatically 're-close' after being disarmed

inside

of the schedule. This allows limiting the

time that authorized users can remain in the

area during the schedule (e.g., cash machines,

vaults, etc.).

- Work Late Input:

When someone presses a

work-late button in this area (during the 'pre-arm

cycle), the scheduled closing time with be set as

{

value selected here

} from the present time.

Note:

A worklate button is a custom input point with

its 'pre-process' set as "Worklate". To define a 'work

late' input-point, refer to "Input Points—Custom Point

Types", and "Input Points—Monitored Sensors".

- Limit Work Late to Midnight:

User's ability to

'Work Late' (i.e., override the scheduled 'Close'

time) for this area will be limited to not extend

beyond midnight.

- Transmit Fail to Close:

Transmit a "Fail-to-

Close" to the monitoring station if the area has

not been armed at the scheduled closing time.

- Auto Arm on Fail to Close:

The area will auto-

arm at the scheduled closing time. This cannot

be used in conjunction with 'Stay on Fail to Exit'

(described above).

-------------------------

- Allow Out of Schedule Opens:

Whether or not

users

without

'24-hr' authority will be able to

gain entry and/or disarm this area outside of

its

open/close schedule, and/or adjust the area

closing time (i.e., 'worklate') after

their

schedule

has expired. (For a non- scheduled area, this

concept does not apply, since only 'Disarm'

authority would be required.) For details on user

authorities, refer to "Authorities for

Users/Entrants".

Stay-Off-Stay Scheduling

- Schedule:

A schedule to be associated with

automated stay/off/stay arming in this area (also

see next setting).

Tip:

Pause the mouse cursor over a schedule in the

list to see the settings for that schedule.

- Auto Stay Mode:

Specifies that the area will

automatically switch from 'Stay' to 'Off', and then

'Off' to 'Stay', in-sync with schedule chosen

above. This will not occur if the area is fully

armed (ON) at the applicable times.

+ None:

Disables this feature (same as selecting

"None" for the schedule.

+ Non secure Disarm to Off:

The area will disarm

(e.g., at the start of the day) if it is in 'stay' mode at

the specific time;

+ Secure Disarm to Off:

For the area to be

disarmed (to off) at the scheduled time, the area

must be armed to 'Stay', and it must have been fully

armed once since the last cycle (ensures someone

was in the facility to arm the area at some time);

+ Disarm to Off Pending First Valid User:

The area

will disarm to off if it is in 'stay' mode at the

scheduled time, but the change will not occur until a

valid user is granted access into the area.



Miscellaneous



- LCD Name:

A shorter version of the name to be

displayed at LCD keypads. This is assigned

automatically, and can also be changed if

desired (max. 12 chars., plain text).

- Require Function Key PIN:

Whether or not the

programmable hot-keys 6-9 & 0 will require a

user with "Function Key" authority to be logged

in. (Function keys 1-5 do not require ID/PIN

entry, except at a portable/wireless arming

keypad).

Tip:

This setting is recommended to help protect

against false alarms.

For details on

using

the function keys on a system

LCD keypad, refer to the MONITOR AFx

(panel/keypad) User's Guide.

What each function key does is set up under

"Programmable Outputs".

To enable function-key authority for a user, refer to the

"Function Keys" setting under "Authorities for

Users/Entrants".

1 2 ... 186 187 188 189 190 191 192 193 194 195 196 ... 323 324

Verex MONITOR AFx Uživatelská příručka Strana 191

Komentáře k této Příručce

Verex MONITOR AFx Uživatelská příručka Strana 191

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Verex MONITOR AFx